Welcome to Slack Science, the place for all things slackline. Here you will find various articles and videos dealing with various aspects of the sport of slackline. Whether you are looking for info on what pulleys to purchase, how to rig a highline, or just some tips for walking slacklines, Slack Science is the place for you!
Remember, if you enjoy what you are ready, be sure and donate what you can to the cause. It takes a lot of time to write up these articles and every bit of assistance helps! Thanks for reading our articles and happy slackin!
All About Webbing Anchors
Webbing Anchor's are an essential part of your slackline setup. Without them we would have to use knots with our webbing, which can very easily destroy the webbing with very little use.
What is a Webbing Anchor?
The most important features of a webbing anchor are the strength (MBS) of the device, the webbing strength retention (how much of the webbing's strength is retained when anchored with said device), and whether or not it is adjustable.
The Shackle Line-Locker Combo Kit comes with two line-lockers built on two different types of shackles. One of the line-locker's is built on a Van Beest 5/8" Bolt-Type Anchor Shackle and is meant for the non-tensioning side of your slackline due to the large shackle size. The other one is built on the bow side of a Van Beest 1/2" Screw Pin Anchor Shackle and is meant for the tensioning side of your slackline as the smaller shackle can connect directly to any of the pulleys offered in the Shop.
The way a line-locker works is a bight (fold) of webbing is passed through a pair of rings and wrapped around the pin (or bow) of the shackle, back through the rings again, and then on to the pin (or bow) of the shackle. These multiple wraps around curved objects cause the webbing to bend in multiple ways which leads to non-uniform loading of the fibers across the width of the webbing. The outer fibers especially see much higher loads than the center fibers, which can cause them to become damaged quite easily. This is why when using a line-locker as a Webbing Anchor, it's very important to use a line-sleeve to protect the line from damage.
Notice in the above picture that the webbing forced to bend when passing through the rings, then is forced to bend the opposite way when going around the pin of the shackle, and then again the other way when it goes through the rings again. The small parts between the changing bends experience a very large difference in tension, especially with lower-stretch webbings (such as Mantra MKII and Spider Silk MKII). It is recommended to not use any sort of line-locker with these lower-stretch webbings as this method can damage the line at even the smallest of loads (800-1000 lbf is a common tension to start seeing damage to the line when using line-lockers with low-stretch webbing).
However, using line-lockers with higher-stretch webbings such as Type-18, 1" Slack-Spec Tubular, and 1" Threaded Slack-Spec Tubular, is perfectly fine. I have seen a 98% strength retention with Type-18 in a 5/8" Shackle Line-Locker Kit. This is because the higher stretch of the nylon fibers allows the webbing to bend around curves without causing much of a difference in stretch across the width. If the outer fibers stretch 1% more than the inner fibers, it will matter much less on a webbing that has a 15% stretch compared to one that has just a 7% stretch.
The strength retention of the Shackle Line-Locker Combo Kit depends greatly on what type of webbing you are using. For nylon webbings, you can see as much as 98% strength retention. For polyester webbings, this number drops down to 80% (this needs further testing). For high-tech fiber webbings, such as Spider Silk MKII, the strength retention drops down as low as 50% (needs further testing). As you can see, line-lockers are best used with high-stretch webbing. When using low-stretch webbing, it's best to use WebLock type devices, as described below.
A huge advantage of line-lockers is that the components typically have amazingly high breaking strengths (typically in the 20,000 - 30,000 lbf range). This is due to the fact that they use ready made components that were meant for overhead lifting.
Line-Lockers are also non-adjustable, which makes them quite a bit harder to use as you have to correctly predict how much room to leave for tensioning when setting up your slackline.
The way that the Alpine WebLock 2.1 works is that a bight (fold) of webbing wraps around the center diverter and is then connected to the front pin. This allows the webbing to be adjustable in one direction while retaining a large percentage of its breaking strength, depending on the size of the center diverter. It also keeps the webbing in good condition because there are no bends that the webbing is forced to go through.
Strength retention depends greatly on the the thickness of the webbing, the size of the center diverter, and the stretch of the webbing. When the webbing goes around the center diverter of the -Alpine WebLock 2.1, the outer fibers are elongated while the inner fibers are compressed (see picture below). This causes the outer fibers to hold a higher percentage of the force compared to the inner fibers. The thicker the webbing, the greater the difference is. Also, the smaller the diameter of the diverter, the great this difference is. For nylon webbings, you can expect a 98% strength retention. Polyester webbings range from 90-98%, depending on the thickness. High-Tech fiber webbings can drop down to 80-85% (need further testing). Be aware that nylon and high-tech fiber webbings can and will slip at around 5,000 lbf when used with the Alpine WebLock 2.1, so be sure to use the double-wrap method when you are going to high tensions and tie off your tail if you plan to use the single-wrap method.
The strength of the Alpine WebLock 2.1 is greater than most of the slackline webbings on the market at 45 kN (10,000 lbf). This makes it ideal for use in alpine environments as the weight has been minimized such that it's not overbuilt for the application.
One of the main advantages of the Alpine WebLock 2.1 is that it's adjustable. This feature not only cuts down rigging time, but it also allows you to use less rope in your pulley system. You can easily bring the line up to 50-100 lbf of tension simply by pulling on the tail coming out from the Alpine WebLock 2.1. You can reduce your pulley system rope length by as much as 15% using this method, which cuts down the weight even further!
The MONSTER Lock
The MONSTER Lock includes one semi-adjustable webbing anchor with the option to include a Van Beest 5/8" Bolt-Type Anchor Shackle and/or a set of bolts/nuts/washers to attach directly to either one or two SMC 3" Double PMP's for your tensioning side anchor.
The way the MONSTER Lock works is quite complex and you should watch the MONSTER Lock Instructional Video for more info on this (or visit the MONSTER Lock Product Page). Basically there are three modes of anchoring, all of which have a purpose during rigging. Mode zero and mode 1 are both adjustable, where-as mode 2 is not. However, the strength benefits of mode 2 far exceed the need for adjustability.
The strength of the MONSTER Lock is at 100 kn (22,480 lbf), which is up there with the line-locker method. This is because the components are made from the highest-strength materials available. This device was built for extreme slacklines where the gear is being pushed to its limits.
As far as strength retention goes, the MONSTER Lock is guaranteed to hold 99.99% of the strength of your webbing. This means that whatever webbing type you are using, you can be sure that it will not break or slip in the webbing anchor until the full strength of the line has been reached. This is a unique feature of the MONSTER Lock and is due in large part to the 3.25" diameter roller. The phenomenon where the inner fibers stretch more than the outer when going around a bend is negligible in the MONSTER Lock.
Here is a nice table comparing the anchors to one another:
|Attribute||Shackle Line-Locker Combo Kit||Alpine WebLock 2.1||MONSTER Lock|
|Device Strength||20,000 - 30,000 lbf||45 kN (10,000 lbf)||100 kN (22,480 lbf)|
High-Tech Fiber Webbing
Mode Zero: Yes
Mode 1: Yes
Mode 2: No
|Price||$71.95 for the pair.||$119.95 each||$259.95 each|
- Line Sleeves - Rigging Practices Feb 20
- Wind Dampeners - Rigging Practices Mar 28
- SMC 3-inch Doubles VS Rock Exotica Mini Machined Doubles - The showdown! - Field Tests Apr 11
- Petzl GRIGRI 2 vs. RIG vs. I'D as a Slackline Pulley System Brake - Field Tests May 30
- Edelrid Eddy as a Slackline Pulley System Brake - Field Tests Jul 06
These articles take a lot of time and research. Help keep Slack Science afloat with a small donation. Every little bit helps.